Just about every person has got their private theory on the subject of A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently obtainable, the task can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will certainly assist you set up a new bathtub in your bathroom if you have actually currently gotten a new tub and don't require to transform the plan of your previous supply of water pipes.
Your tools and also product checklist should comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipes have been gotten rid of, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in area between the tap and also the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Tub
Making use of both wooden boards under its feet, position the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the tub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, repair the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of once as this will resolve it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface in between the bath and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily offered on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report on How to Install a Bathtub through a good friend on a different domain. Sharing is good. One never knows, you might be doing someone a favor. We appreciate reading our article about How to Install a Bathtub.
Visit Our Website